Skip to main content

What equipment is used for drying of tailings?

Tailing is one of the products of the sorting operation in the beneficiation, in which the part with the lowest content of useful target components is called tailings. 

Tailings are not completely useless waste, and often contain components that can be used for other purposes and can be comprehensively utilized. Achieving no waste discharge is a requirement for the full utilization of mineral resources and the protection of the ecological environment.

Tailing drying screen is designed for the dewatering of tailings.

tailings drying dewatering screen


Technical characteristics of tailings dewatering screen:

1. High working frequency, high vibration intensity, low moisture content of the product on the screen, high unit processing capacity, and high solid recovery rate when used for dewatering tailings.


2. Using the principle of self-synchronization, the motor drives the vibrator through a tire coupling, with simple structure and low working noise.


3. Installation with negative inclination angle, the screen surface of the pre-dewatering section is installed at 45 degrees from the horizontal, increasing the dewatering area and promoting the material to be dehydrated as soon as possible to form a filter layer.

sand dewatering screen

4 The screen surface adopts polyurethane elastic screen surface, which has high open rate and elasticity, which is beneficial to dehydration.


5. The vibrator is an eccentric unit structure, which is easy to disassemble and maintain.


6. The bearing adopts special bearings for vibration equipment to avoid premature damage to the bearing due to heating.

Comments

Post a Comment

Popular posts from this blog

Sandblasting nozzle classification and use

Using high-pressure air as a power source to drive abrasive particles to hit objects within a certain range will produce a great impact. The function of the sandblasting nozzle is to spray abrasive particles on the object evenly and efficiently. Sandblasting nozzles can be divided into: straight hole sandblasting nozzle, Venturi sandblasting nozzle , double Venturi sandblasting nozzle, angle sandblasting nozzle Straight hole nozzle: There are only contraction section and straight section inside, the structure is simple and easy to manufacture. This kind of nozzle cannot overcome the vortex phenomenon existing at the inlet end, and the pressure loss is large; the abrasive velocity at the outlet is less than 100m/s under the pressure of 0.7MPa.
Post a Comment
Read more

Working principle and parameters of industrial slurry pump

In order for the industrial slurry pump to fully play its role, we need to understand the working principle of the industrial slurry pump: https://www.lzzgmachine.com/products/supporting-equipment/slurry-pump.html Under the action of centrifugal force, the liquid is thrown from the center of the impeller to the outer edge and gains energy to leave the outer edge of the impeller at a high speed and enter the volute pump shell. In the volute pump case, the Fluid is slowed down due to the gradual expansion of the flow channel, and part of the kinetic energy is converted into static pressure energy. At last, it flows into the discharge pipe and is sent to the place where it is needed. When the liquid flows from the center of the impeller to the outer edge, a certain vacuum is formed in the center of the impeller. Above the liquid level of the storage tank is greater than the pressure at the pump inlet, the liquid is continuously pressed into the impeller. LZZG slurry pump pe...
Post a Comment
Read more

The difference between quartz and mica

Mica and quartz are common minerals that play an important role in mineralogy. Although they are both silicate minerals, there are clear differences between them. First, mica and quartz are very different in appearance. One of its distinguishing features is that mica exhibits a layered structure that can be easily peeled off into thin flakes. Quartz, on the other hand, is a uniform crystal with no layered structure. Additionally, mica is usually dark in color, such as black, brown, or green, while quartz is usually clear or white. Secondly, mica and quartz also differ in their physical and chemical properties. The hardness of mica is usually between 2.5 and 4, which is relatively easy to be scratched; while the hardness of quartz is very high, 7, which is a very hard mineral. In addition, mica has good refractive properties and electrical properties, while quartz is an excellent piezoelectric material.
Post a Comment
Read more