Skip to main content

Dewatering screen failure quick elimination method



High frequency dewatering screen cannot be started or the amplitude is too small

Should first consider whether the motor is damaged, or whether the components in the line are damaged, or the local voltage is insufficient at the time. If there is no problem in these three aspects, then it should be checked from the machine, and the material on the screen surface should be piled up too much. Clear it immediately. Since the accumulation of too much material directly affects the amplitude of the vibrating screen. Whether the coupling bolt on the vibration exciter is detached or not, and the grease is thickened and agglomerated. At this time, the exciter can be cleaned and the eccentric shaft weighting block or the position of the sub eccentric block can be appropriately adjusted.

Abnormal material activity on the screen

It may be that there is an insufficient critical frequency of the screen box, indicating that the coupling bolt has been loosened, and even the degree of full vibration needs to be tightened immediately. Second, the horizontal level of the screen box is not fixed, and the fault is detected from the support foot spring itself. The spring or the size of the pad or the seat can be changed, and the screen mesh may be damaged. Just replace the screen. If the rigidity of the screen box is insufficient, the horizontal level will not cause the beam to break. If it is still running, the material will be abnormal. It is also possible that mishandling, that is, the extreme imbalance of the feedstock is also one of the reasons.

The vibrating screen rotates slowly and the bearing heats up.


This shows that the usual maintenance has not kept up, the bearing lacks grease; daily maintenance is also very important. If the bearing is a new grease, it may be the quality of the grease or too full, the inferior oil makes the bearing obstruction maze seal jam, so the quality of the grease is important. The quality of the vibrating screen is not good. The reason is that improper use may also be blocked by the mesh. The fine particles in the feed material increase and the moisture increases, so that the upper layer of the screen is too thick and the feeding is uneven. The responsibility on the machine may be screen. The two sides are not pulled tightly. If the shaft is eccentrically vibrated, the belt may be too loose in the belt drag.



The drum screen belongs to the relatively large processing equipment in the screening equipment. Although there is no complicated structure of the magnetic separator and the sorting machine, the processing amount is large during the use, so it is inevitable that some mechanical equipment will appear during the long-term use. The failure of the technical experts gives the corresponding solution.

1. Noise problem caused by loose equipment bolts Solution: Retighten bolts or other fasteners;
2. Wrong direction of rotation caused by wrong connection of motor power cables Solution: Replace the power cable in the junction box;
3. Solution to the clogging of the sieve of the trommel screen

https://www.lzzgmachine.com

Comments

Post a Comment

Popular posts from this blog

Sandblasting nozzle classification and use

Using high-pressure air as a power source to drive abrasive particles to hit objects within a certain range will produce a great impact. The function of the sandblasting nozzle is to spray abrasive particles on the object evenly and efficiently. Sandblasting nozzles can be divided into: straight hole sandblasting nozzle, Venturi sandblasting nozzle , double Venturi sandblasting nozzle, angle sandblasting nozzle Straight hole nozzle: There are only contraction section and straight section inside, the structure is simple and easy to manufacture. This kind of nozzle cannot overcome the vortex phenomenon existing at the inlet end, and the pressure loss is large; the abrasive velocity at the outlet is less than 100m/s under the pressure of 0.7MPa.
Post a Comment
Read more

Working principle and parameters of industrial slurry pump

In order for the industrial slurry pump to fully play its role, we need to understand the working principle of the industrial slurry pump: https://www.lzzgmachine.com/products/supporting-equipment/slurry-pump.html Under the action of centrifugal force, the liquid is thrown from the center of the impeller to the outer edge and gains energy to leave the outer edge of the impeller at a high speed and enter the volute pump shell. In the volute pump case, the Fluid is slowed down due to the gradual expansion of the flow channel, and part of the kinetic energy is converted into static pressure energy. At last, it flows into the discharge pipe and is sent to the place where it is needed. When the liquid flows from the center of the impeller to the outer edge, a certain vacuum is formed in the center of the impeller. Above the liquid level of the storage tank is greater than the pressure at the pump inlet, the liquid is continuously pressed into the impeller. LZZG slurry pump pe...
Post a Comment
Read more

The difference between quartz and mica

Mica and quartz are common minerals that play an important role in mineralogy. Although they are both silicate minerals, there are clear differences between them. First, mica and quartz are very different in appearance. One of its distinguishing features is that mica exhibits a layered structure that can be easily peeled off into thin flakes. Quartz, on the other hand, is a uniform crystal with no layered structure. Additionally, mica is usually dark in color, such as black, brown, or green, while quartz is usually clear or white. Secondly, mica and quartz also differ in their physical and chemical properties. The hardness of mica is usually between 2.5 and 4, which is relatively easy to be scratched; while the hardness of quartz is very high, 7, which is a very hard mineral. In addition, mica has good refractive properties and electrical properties, while quartz is an excellent piezoelectric material.
Post a Comment
Read more